YuanLey 8-Port Gigabit PoE+ Switch with 2 Uplinks and SFP Review
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This YuanLey switch has 11 gigabit ports: eight PoE+ ports sharing a 120W budget (up to 30W each), two gigabit uplinks and one 1G SFP slot for fiber. It suits a small camera or access-point setup that needs more than one uplink. Compared with YuanLey's plain 8-port PoE+ model, it adds the uplinks and SFP for a little more money; compared with TP-Link's TL-SG1210P (8 PoE+ at 63W, one uplink plus SFP), it gives nearly twice the PoE budget for less. The power supply is built in, and the switch only powers standard 802.3af/at devices, not 24V passive PoE. We compared listings and published specs; the switch was not used for this review.
What stands out
- 8 gigabit PoE+ ports, 120W total
- 2 gigabit uplinks + 1G SFP slot
- Port isolation mode for ports 1-8
- Watchdog restarts a frozen PoE device
Who it fits
Good fit for
Small CCTV or Wi-Fi access-point installs with up to eight 802.3af/at devices, where a fiber run or a second uplink to an NVR or router is useful.
Who should skip it
Owners of 24V passive PoE gear (not supported), anyone who needs VLANs they can configure (this is unmanaged), or setups that need 2.5G ports.
Verdict: Good value for an 8-camera or 8-AP install that needs an SFP uplink.
YuanLey 11-port PoE+: key specs
8 x gigabit PoE+
802.3af/at, up to 30W per port.
120W PoE budget
Enough for eight typical cameras; high-draw PTZ cameras or Wi-Fi 6 APs can use most of it.
2 x gigabit uplink + 1 x 1G SFP
Uplinks to a router or NVR; the SFP slot takes a fiber module for longer runs.
Isolation on ports 1-8
PoE ports can talk only to uplinks 9-11, not to each other.
QoS on ports 1 and 2
Traffic on these ports is forwarded first under congestion.
7.9 x 4.7 x 1.7 in, 2.13 lb
Metal case with built-in power supply.
Metal box, no power brick
The YuanLey case is blue metal, about 7.9 x 4.7 x 1.7 inches, with the power supply inside, so only a plain power cord goes to the wall. The listing calls it noiseless; it does not state fan or fanless. Ports 1-8 carry PoE, 9 and 10 are the uplinks, and 11 is the SFP slot.
Running cameras and APs
Out of the box the switch is plug-and-play. The isolation mode keeps PoE ports from talking to each other, which limits traffic between cameras and sends everything to the uplinks, where the NVR or router sits. The AI watchdog spots a PoE device that has gone offline and power-cycles it, which saves a trip up a ladder for a hung camera. QoS on ports 1 and 2 gives two key devices first place in a queue.
This YuanLey, the plain 8-port YuanLey or TL-SG1210P?
Choose this 11-port YuanLey when you need eight PoE+ ports plus separate uplinks or an SFP fiber link. Choose YuanLey's plain 8-port PoE+ switch if every device is close and one PoE port can serve as the uplink. Choose TP-Link's TL-SG1210P only if you want the TP-Link brand and your devices fit in its 63W budget.
Check before you buy
- Devices use 802.3af/at, not 24V passive
- Total draw under 120W
- Need an uplink or fiber link
- No configurable VLANs needed
The product at a glance
YuanLey 8-Port Gigabit PoE+ Switch with SFP
Best for: Small CCTV and AP installs
- Port Count
- 11
- Port Speed
- 1000Mbps
- Management Type
- Unmanaged
- PoE Support
- 802.3af/at
- PoE Power Budget
- 120W
- Uplink Ports
- 2 Gigabit uplink, 1 SFP
View on Amazon: YuanLey 8-Port Gigabit PoE+ Switch with SFP Affiliate link
11-port YuanLey gigabit switch: 8 PoE+ (120W), 2 uplinks and an SFP slot.
Pros
- 120W budget, 30W per port
- Two uplinks plus SFP
- Watchdog auto-restart
Cons
- No 24V passive PoE
- Not managed
- Fan or fanless not stated
Good fit if
- Eight cameras or APs need an uplink or fiber
Skip if
- You need configurable VLANs
Verdict: Strong value for small PoE installs with a fiber or second uplink.
Specifications side by side
| Spec | YuanLey 8-Port Gigabit PoE+ Switch with SFP |
|---|---|
| Port Count | 11 |
| Port Speed | 1000Mbps |
| Management Type | Unmanaged |
| PoE Support | 802.3af/at |
| PoE Power Budget | 120W |
| Uplink Ports | 2 Gigabit uplink, 1 SFP |
| Number of Ports | 8 Ports |
| Uplink Port Type | SFP, Gigabit Uplink |
| Dimensions | 7.9 × 4.7 × 1.7 inches |
| Weight | 2.13 pounds |
| Size | 11 Port | 8*PoE+(1000Mbps) (120w) |
| Color | Blue |
| Model | 11 Port | 8*PoE+ (1000Mbps) (120w) |
Frequently asked questions
How many PoE ports does this YuanLey switch have?
Eight PoE+ ports; the two uplinks and the SFP slot carry data only.
What is the PoE budget per port?
Each PoE+ port gives up to 30W, within a shared 120W for all eight.
Can it power 24V passive PoE radios?
No. YuanLey states it is not compatible with 24V passive PoE.
What does the watchdog do?
It detects a PoE device that has failed or gone offline and restarts it automatically.
Is the switch managed?
No. Isolation and QoS are fixed modes; there is no web interface.
Featured in
See also
- steamemo 16 port managed poe switch 240w review
- ubiquiti unifi usw aggregation 10g sfp switch review
- ugreen 6 port gigabit poe switch review
- yuanley 8 port gigabit poe review
- yuanley 8 port poe switch review
- YuanLey 18-Port 2.5G Switch with 10G SFP+ Review (2026): A Spec-Based Look
- hiseeu 8 camera 12mp poe security review
- annke 8 channel 4k poe system review
