ADnet 2-Wire Ethernet Extender Kit Review: 600 m over Copper or Coax
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
The ADnet Ethernet Range Extender Kit is a wired solution, not Wi-Fi: a pair of powered units that carry a 10/100 Ethernet link up to 600 m (2,000 ft) over any two copper wires. That can be a spare pair in an existing Cat5e or Cat6 run, alarm or intercom wire, or old RG59/RG6 coax through the included BNC adapters. The link rate across the span is up to 92-100 Mbit/s and falls with distance and wire quality. Both units need mains power (two 12-24 VDC adapters are included), there is no software, and VLAN tags, DHCP and camera streams pass through unchanged. Pick it for a barn, gate camera or outbuilding where only old wire exists; it does not add Wi-Fi by itself, so put an access point or router at the far end if you need wireless. Based on the listing and maker's specs; we did not test it.
What stands out
- 600 m over any two copper wires
- Works over coax with BNC adapters
- Transparent: VLANs, DHCP, RTSP pass
- No configuration needed
Who it fits
Good fit for
Anyone who must bring a network to an outbuilding, gate camera or remote office over existing old wiring or coax, where 100 Mbps is enough.
Who should skip it
Anyone wanting Wi-Fi coverage (this is wired only), gigabit speeds, or an outdoor-rated unit: the case has no IP rating.
Verdict: A practical fix for long runs over existing wire, at Fast Ethernet speed.
ADnet kit key specs
Up to 600 m / 2,000 ft
Point to point over two conductors.
Up to 92-100 Mbit/s
Falls with distance and wire gauge.
10/100BASE-T RJ45
Fast Ethernet ports at each end.
Twisted pair, alarm wire or coax
BNC-to-terminal adapters included.
12-24 VDC, under 2 W per unit
Two adapters included.
100 x 86.5 x 25 mm, -20 to +60 C
PC alloy shell, not weather sealed.
Build and box contents of the ADnet pair
The set has a master and a remote unit (the same hardware), two 12-24 VDC power adapters and two BNC-to-wire-pin adapters. Each unit measures 100 by 86.5 by 25 mm in a PC alloy shell with no moving parts, rated -20 to +60 C and 95% humidity non-condensing.
The case is not IP rated, so for an exterior location mount it in a sealed enclosure.
Installation and use
Connect the two wires to the screw terminals (or coax through the BNC adapters), plug a patch cord into each unit and power both ends; the link comes up with no driver or setup. Twisted pair reaches furthest; mixed runs of coax and untwisted wire lower the rate but keep the link.
Because the span is a transparent Layer 1 segment, IP cameras, NVR discovery and VLANs work as on a plain cable. At the far end, add a switch for several devices or a Wi-Fi access point for wireless.
ADnet kit, Wi-Fi bridge or outdoor extender?
Choose the ADnet kit when a copper pair or coax already reaches the building and you need a stable wired link up to 600 m. Choose a Wi-Fi bridge pair or an outdoor extender such as the WAVLINK AC600 outdoor unit when there is clear line of sight but no wire. Choose new Cat6 if the run is under 100 m: plain Ethernet needs no power at the far end and supports gigabit.
Check before you buy
- Two continuous copper conductors or coax
- Mains power at both ends
- 100 Mbps is enough for the far end
- Weatherproof box for outdoor mounting
The product at a glance
ADnet Ethernet Range Extender Kit
Best for: Long Ethernet runs over old wire
- Ethernet Ports
- 10/100BASE-T
- Operating Mode
- Bridge Mode
- Weight
- 1.19 pounds
View on Amazon: ADnet Ethernet Range Extender Kit Affiliate link
ADnet 2-wire Ethernet extender kit: 10/100 Ethernet up to 600 m over any copper pair or coax, transparent to VLANs and cameras, no setup; wired only.
Pros
- Uses existing wire or coax
- Up to 600 m reach
- Plug-and-play pair
Cons
- Fast Ethernet speed only
- Case not weatherproof
- No Wi-Fi
Good fit if
- Old wire already reaches the site
Skip if
- You need gigabit or wireless
Verdict: Good for long wired runs at 100 Mbps.
Specifications side by side
| Spec | ADnet Ethernet Range Extender Kit |
|---|---|
| Ethernet Ports | 10/100BASE-T |
| Operating Mode | Bridge Mode |
| Weight | 1.19 pounds |
| Color | Black |
Frequently asked questions
Does the ADnet kit create Wi-Fi?
No. It extends a wired Ethernet link; add an access point at the far end for Wi-Fi.
How far can the ADnet kit reach?
Up to 600 m (2,000 ft), with speed falling as distance grows.
Can it run over coax?
Yes, RG59 or RG6 through the supplied BNC adapters.
What speed does it deliver?
Up to 92-100 Mbit/s across the span; the RJ45 ports are 10/100.
Do both ends need power?
Yes, each unit has its own included 12-24 VDC adapter.
See also
- asus rp ax58 ax3000 wifi 6 extender review
- asus rp be58 be3600 wifi 7 extender review
- wavlink ac600 outdoor access point review
- best mesh wifi systems under 100
- best mesh wifi systems under 150
- Best Mesh Wifi Systems Under $200: 10 Spec-Based Picks
- 9 Best Mesh Wifi Systems Under $300, Compared
- Best Mesh Wifi Systems Under $500 in 2026: 8 Picks Ranked by Specs
- iokofjoa power extender kit c wire review
- avanti electric range review
